Creality K1 Series CFS Upgrade Kit
The CFS upgrade kit is showing in stock on the Canadian store site.
Karve Shaving Co is Canadian as well.
You have to stand up and fight the tyranny. Id like to tell you that peaceful things or court action would help, but I think you better start reading up on the second amendment.
I'm sure there will be a swift response, hahahahaha I can't even finish it. There will be nothing, just Americans rolling over and taking it cause daddy Cheeto said so..
America, again get your fucking house in order.
Seems that way, yes people are starting to protest but not nearly enough, and as another commenter mentioned the media is not covering it, which should surprise no one.
The Democratic party needs to be laying out the facts when the CiC lies to the people, but nope they seem to be just sitting back sulking saying "see we told you this would happen and since you didn't vote us in we're not going to do shit"
Was she voted in or was she handed the position due to someone quitting.
That's what happened in Canada with Kim Campbell and she was voted out at the first election, and same now with Mark Carney, he is the PM now but was not voted in, so we will vote on the 28th to see.
But it does seem like Thatcher and Regan types are back in style.
That doesn't seem to be saying much though. lol
Is she the MTG of the UK?
Spot on!
Why do you think that is, I'm not screwing around but curious. Is it actually because of the military strength it helps the US project in the area or is there some other reason. I truly cannot understand why this is being endorsed by so many people and governments.
It is very strange to see how everyone capitulates on the whole ordeal. If you can't recognize and call out a genocide for fear of backlash and attacks, then it should be obvious that very powerful people are pulling the strings.
It is quite disgraceful that governments and organizations are not calling it what it is for fear of something or someone.
But they're not the "right" beliefs, and since your government is now an evangelical Christian government everyone is wrong if their beliefs don't match.
What a bunch of fucking idiots. That'll be the new channel on Rumble "Fat White Fucks Fighting While Golfing" it'll show up right behind that stupid slap shit.
Idiots
They should listen, right now do more to do the US. Don't listen make other trade deals, their the same shit back to them, stop taking them serious, put them in the penalty box now.
Really the carbon tax was funding the CRA?
They should have any remaining kids removed, how sad that for something preventable a child has died because of its parents.
Canada should have done this on everything. If the Americans can afford the tariff then there is room for us to charge more. Not really but yeah should do it.
What a joke, neither one has the power to bring him back, which fuck had the power to send him and accept him.
Both are complicit. Fucking dog and pony show.
America get your house in order.
Yeah and through careful planning we can reduce that number to less than 1. Soon people will stand up to these blood suckers.
If they were smart they'd want it for the reduced cost of cooling their data centres.
I wish I could take credit for that.
Creality K1 Max Curves Surface Issue
I have a K1 Max and mostly it is running great, however I get strange artifacts on mostly only the front side of curved objects.
I have lubed all the rods, and I have a Capricorn PTFE tube from the filament sensor to the hot end. I tried the printable guide for the tube to go into the hot end but it wasn't any better and I thought that was the culprit at first.
I have an extension piece to raise up the top glass.
I'm using Elegoo Rapid PTEG running at 240c and 250mm outerwall speed. This is mainly happening on the front side and anywhere on the build plate. Filament is dry and fed out of the Creality Space dryer.
These items are small netcups but it was also happening on the larger sections that they go in.
Using Orcaslicer and Arachne wall generator.
Elite C Firmware Issue
Hey all, working on a Corne Choc, and having issues flashing the right half of the board with QMK Toolbox.
I am getting a validating error with:
822 invalid byte in program region, 0 outside region
This is the second controller as I had the same error on the first and assumed I ruined it when I was troubleshooting it and desoldering.
Ordered a new board and same issue.
I've cleared the EEPROM, there are not shorts or bad solder on the headers. This is a completely separate PCB.
Tried using QMK MSYS to reflash ISP (not sure I got that right, don't really understand it).
Get a blue led indicating power, reset button works to put it into bootloader mode, still nothing will flash on it.
Unfortunately on the first go round I had soldered headers to swap but was too tall for me, desoldered the boards and went directly to the PCB, as mentioned this is a new board on a new PCB, did not program prior to soldering.
Upgraded Ender 3v2 Issues
I've had an Ender 3 v2 for a few years now and have had mostly no issues. I've upgraded the hot end to a microswiss direct drive and a dual z setup (twin z steppers on a shared cable).
Recently started having issues with the 4.2.2 board and replaced it with a BTT mini SKR 3 v3.
Since I've put the new board in, I am having troubles getting the bed to level and stay level.
The height profile of the bed is now showing a dip in the centre (which was not there before). When I run a print it seems to be overcompensating for the dip. If I level the bed with the corner screws and don't use the bed mesh then it prints fairly good, but after a few prints the bed goes out of level again.
I can't seem to make any adjustments that help the issue. Yesterday tightened up all the screws (silicon spacers instead of springs). Releveled the bed and had a small dip in the middle and an overall height difference of 0.170 across the bed (normal prior to this was 0.310). Sent a print with bed mesh and m